Base-lime products ideal for rehabilitation, restoration and new construction. Porosity and breathability make it ideal for rooms with relatively high humidity levels.

Easy application products that only require long-term maintenance.

Old aerated lime paste, base for the preparation of mortars, paintings,... compatible with all base materials for construction, except gypsum. Aggregated and sieved aerated lime dough, a base for high-decoration paint and stucco. Air lime mortar with thick aggregate, provides thermal and acoustic insulation, gives planimetry. It can be used as a base and finished product. Mortar of aerial lime with fine aggregate, is a finishing product, suitable for interiors and exteriors. Available in several colours. Air lime mortar with extrafine aggregate, finished product with a totally smooth result, similar to marble. Depending on its application, different textures are obtained. Available in several colours.

Acrylic enamel useful for protection and decoration works in general; its property of not becoming yellow makes it suitable for painting radiators and heating pipes. It is recommended to be used in hospitals, restaurants and operating rooms due to its quick drying capacity and lack of odours. Also indicated for labelling.

Solvent-free biocomponent epoxy primer, of fast curing and applied at low temperatures. Properties: cured at low temperature, low viscosity, easy to apply, excellent penetration in the support, it seals pores and capillaries and excellent adhesion on the support.

MASTERTOP P 617 FAST is designed for indoor and outdoor use as a primer on mineral substrates, such as concrete and mortar with MASTERTOP flooring systems and CONIPUR waterproofing systems, when the temperatures are too low for a general purpose epoxy primer or in those applications where reducing the curing time is an important parameter.

MASTERTOP P 617 FAST is supplied in sets of 15.3 kg.

Self-levelling polyurethane coating for decorative pavements. Bi-component, solvent-free polyurethane coating, self-levelling, elastic, pigmented, of low emission, stable colour and resistant to UV rays for decorative floorings. Properties: Low emissions according to AgBB, stable to colour, resistant to UV rays, elastic, high degree of comfort when footing, noise absorption, resistant, robust, crack tapping capacity, easy to apply and excellent self-levelling capacity.

MASTERTOP BC 361 N is a self-levelling coating of aliphatic polyurethane bicomponent pigmented for floors, free of solvent and of low emissions, which hardens forming an elastic material, resistant, easy to maintain and tolerant to a wide range of cleaning chemicals and variety of chemical compounds. Due to its aliphatic nature, MASTERTOP BC 361 N is stable in colour and resistant to UV rays. MASTERTOP BC 361 N can be used fresh on fresh in order to realize decorative polychromatic floorings. It is the basis of the MASTERTOP 1326 and MASTERTOP 1327 D systems, a range of decorative pavements specially designed for use in boutiques, day-care centres, bars and restaurants, reception areas and offices.

MASTERTOP BC 361 N is supplied in sets of 13 and 26 kg.

Bi-component polyurethane coating free of solvents, self-levelling, elastic, pigmented and of low emissions. Properties: Low emissions according to AgBB, excellent self-levelling capacity, resistant to abrasion, robust, excellent deaerating ability, easy to clean and maintain, tapping ability of static fissures and good chemical resistance.

MASTERTOP BC 375 N is used indoors where resistance to medium to heavy traffic is required. It is suitable for mineral substrates such as concrete and mortar, previously primed with MASTERTOP epoxy primer. It can also be applied on bituminous supports with a previous primer with the own MASTERTOP BC 375 N. It is part of the MASTERTOP 1324 pavement range.

MASTERTOP BC 375 N is supplied in sets of 30 kg.

Properties: Reduced viscosity, excellent adhesion to the substrate, easy to apply, sealed with pores and capillaries of the concrete, moisture tolerant in the support, low emission of volatiles and suitable for application on concrete supports contaminated with oils (after cleaning).

Priming prior to the application of epoxy or polyurethane based coatings MASTERTOP pavements or CONIPUR waterproofing systems (only for manual application) on concrete substrates contaminated with oils and/or gas-oil.

MASTERTOP P 615 is supplied in sets of 16.9 kg.

Solvent-free bicomponent epoxy primer for synthetic coatings on mineral substrates. Properties: Low viscosity, easy to apply, excellent penetration in the support, it seals pores and capillaries, excellent adhesion on the support and low emissions.

MASTERTOP P 617 FAST is designed for indoor and outdoor use as a primer on mineral substrates, such as concrete and mortar with MASTERTOP flooring systems and CONIPUR waterproofing systems. It is possible to use it as a spatula primer by adding MASTERTOP F1 in a ratio from 1: 0.5 to 1: 2. MASTERTOP P 617. It complies with the requirements of the relevant regulations regarding the effect of rising humidity. MASTERTOP P 617 has been tested and classified for its low emissions in systems such as MASTERTOP 1325.

MASTERTOP P 617 is supplied in sets of 18 kg.

Water-based acrylic enamel, formulated with acrylic resins emulsified in water and pigments with a maximum guarantee for indoor and outdoor decoration.

The medium porcelain stoneware product is basically composed of clay, feldspar and sand with an enamel layer composed mainly of feldspar, carbonate, silicates and kaolin, among others.

The main recommended use for this product is for floor paving and/or wall and façade coating, both inside and outside.

The included product is an average porcelain stoneware that includes the following stoneware models: Water absorption group BIb and BIa (Formed by dry pressing with AA between 0.5 and 3% and <0.5% respectively). Commercial name: STON-KER / PAR-KER / STON-KER FACHADAS/ PAVEMENTOS. Nominal formats (cm): 14.3x120x1.2 / 19.3x120x1.2 / 29.4x120x1.2 / 18x65.9x1 / 43,5x43,5x1 / 43x65,9x1 / 59,6x59,6x1,1 / 80x80x1,2 / 59.6x120x1.2.

The Dry-pressed ceramic tile (BIa) product is basically composed of clay, feldspar and sand with an enamel layer composed mainly of feldspar, carbonate, silicates and kaolin, among others.

The main recommended use for this product is for both coating and flooring.

The product included is a dry pressed ceramic tile (BIa) that includes the following formats: Water absorption group: BIa Dimensions (cm): 11.9x24.4; 24.4x24.4; 31x31; 31x62.6; 59.4x59.4; 59.4x119; 15.25x78.25; 24.4x49.4; 5.6x24.4; 32x32; 60x60; 29.6x59.4; 39.5x119; 119x119; 29.8x29.8; 29.8x59.8; 59.8x59.8.

The white tile product is basically composed of clay, feldspar and sand with an enamel layer composed mainly of feldspar, carbonate, silicates and kaolin, among others.

The main recommended use for this product is for both coating and flooring.

The product included is a white tile that includes the following models: Water absorption group: BIII all Trade name: Revestimiento pasta blanca. Nominal formats (cm): 25x40; 20x60; 31x44; 30x90; 29.5x89.3; 30.5x60.5; 29.5x59.5 / 25x40; 20x60; 31x44; 31.6X61.6; 30x90; 29.5x89.3; 30.5x60.5; 29.5x59.5.

Mortar of lime for inner and outer walls finishes of different granulometries. Base of natural, hydraulic and sand lime binder.

It is used as mortar for its execution. It requires the construction of bricks or blocks of bricks where the absence of Portland grey cement and a light coloured grout is required.

Bags of approx. 30 kg with special protection against humidity.

The Eco Klinkers bricks from Piera Ecoceràmica are made from biogas, which reduces up to a 35% the CO2 emissions during the industrial process. Biogas is a clean fuel that reduces environmental pollution. The biogas used by Piera Ecocerámica comes from the treatment of organic waste buried under layers of clay from the Can Mata landfill, located in Hostalets de Pierola. Piera Ecoceramic avoids the emission into the atmosphere of 17,000 tonnes/year of CO2 as well as other greenhouse gases or ozone depleting gases. The Piera Ecoceramic biogas system allows the application of this energy source in the manufacture of the 95% of the Piera's products, contributing to a 45% of the total thermal energy used. Therefore, the manufacturing of products has a low rate of atmospheric emissions and a total commitment to respect the environment. The entire catalog of Piera Ecoceramic is compatible with the Structura system of ventilated and self-supporting façade construction that meets the requirements of the CTE.

The range of Eco Klinkers is marketed in the following models: Venice: 28 x 13.5 x 5.7 - 28 x 12 x 4.9 (cm), Bellaterra: 28 x 13.5 x 5.7 - 25 x 12 x 4.9 (cm), Red Clinker: 27.6 x 13.3 x 4.8 / 5.8 - 24 x 11.5 x 4.9 (cm), Tuareg: 28 x 13.5 x 5/6 - 24 x 11.5 x 5 (cm), Sahara: 28 x 13.5 x 5/6 - 24 x 11.5 x 5 (cm), Tundra: 28 x 13.5 x 5/6 - 24 x 11.5 x 5 (cm). The Eco Klinker from Piera Ecocerámica have a high resistance, above 55 N/mm2 and a low absorption, between the 4 and 5% on average.